Performing an Immediate Scan
To perform a scan without first creating a scan request:
Select the patient record in the patients list 
.
Click Capture 
.
Hover over an available image acquisition device and click Select.
Notes
Hover over a busy image acquisition device and click Release Device to attempt undoing a device reservation.
Click 
to filter on the modality type.
Busy devices are marked by an hourglass. The Select action is disabled until the device becomes available.
The applicable modalities for every image acquisition device are shown at the bottom of the device tile.
Intraoral sensors that are directly connected to your computer via USB are indicated with the Connected 
icon.
If the connection to DTX Studio™ Core or to the image acquisition device is lost, a window will be shown where you try to re-establish the connection by clicking Reconnect or to close the scan module by clicking Close scan.
For a (CB)CT scanner a scout image can be made before starting the actual scan. The scout image is saved on the Patient data tab of the patient record.
Continue the acquisition process for your device.
Notes
You can use multiple sensors with different sensor sizes by plugging them in or out during the capture wizard. The used sensor is shown in the top-right corner. If multiple sensors are plugged in, the + symbol appears. All sensors which are connected and active, are ready to acquire the scan. X-ray triggers the image acquisition.
If you acquire new image data for a patient record that is open and the computer is connected to DTX Studio™ Core, the acquired data will automatically be added to the open diagnosis, except for a (CB)CT scan, which you will have to select separately in the diagnosis data on the patient menu.
If you acquire new image data for a patient record that is closed, and if:
the patient does not have a diagnosis yet, then a diagnosis will be created automatically.
the patient has a diagnosis that was created before today, a new diagnosis will be created.
the patient has a diagnosis that was created today without a 3D scan, then the new image data is added to the diagnosis of today.
the patient has a diagnosis that was created today with an existing 3D scan and you acquired new 3D data, then a new diagnosis is created and the 2D data set of the most recent diagnosis is copied to the new diagnosis.
the patient has a diagnosis that was created today with an existing 3D scan and you acquired 2D data only, then the 2D data are added to this diagnosis.
Intraoral Sensor or PSP Device
Acquire images with a template ( see guided acquisition) or without a template (see free acquisition).
Intraoral Camera
If you acquire with an intraoral camera: the guided acquisition invites you to select the teeth you want to acquire.
Select the teeth you want to acquire.
Click Start.
Note
From within the diagnose module, when removing a portable device, like the Diagnocam Vision Full HD/Carivu 3-in-1, from its holder or treatment unit, an intraoral camera viewer will be added to the workspace for immediate acquisition. When putting the device back into the holder or treatment unit, the active viewer will be removed from the workspace. (Note: Holder detection is not supported on the KaVo ERGOcam One device.)
Go to the device to perform the scan.
Notes
If working with a Diagnocam Vision Full HD/Carivu 3-in-1 device, select Multi shot to acquire all possible image types. When using the tip, three different acquisition modes are used: transillumination, fluorescence and intraoral. Select Single shot and the type of image to acquire one image type at a time.
The defaults are set in the device settings that are accessible via the notification area.
Disable or enable the acquisition helper for a Diagnocam Vision Full HD/Carivu 3-in-1 device by selecting Disable acquisition helper or Enable acquisition helper 
. The acquisition helper comes in the form of green or orange edges on the viewer, indicating good or bad exposure.
Press the button on the device to acquire the image. Alternatively, click Capture image 
in the viewer.
Notes
If your intraoral camera comes with a foot pedal, you can use the foot pedal to acquire an image.
If acquiring images with a Diagnocam Vision Full HD/Carivu 3-in-1 device, Intraoral, Transillumination or Fluorescence acquisition can be selected.
On the smart panel, select the tooth number that will be assigned to the acquired image.
Use the device buttons or click Next or Previous to switch between the teeth.
When done, click Finish.